User Manual () Upgrade Instructions; 07/01/15; Download; Release Notes. Datasheet (). Datasheet () Upgrade Instructions; 08/31/15; Download. Don’t forget about our other Dlink DSLB info that you might be interested in. Login to Dlink DSLB Router · Change your Dlink DSLB IP Address. 5) The power light will first go red and the DSL light will flash. The DSL B comes with a lot of Manual Setup tick box and click the Setup Wizard button.

Author: Kazishakar Sahn
Country: Nicaragua
Language: English (Spanish)
Genre: Finance
Published (Last): 16 February 2013
Pages: 454
PDF File Size: 1.43 Mb
ePub File Size: 18.51 Mb
ISBN: 244-5-45440-246-5
Downloads: 96476
Price: Free* [*Free Regsitration Required]
Uploader: Araran

D-Link DSL 2640B Setup Manual

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

Dsl-264b Information of the Router It is compatible with access servers manufactured by major vendors. Using both versions lets the Router to communicate with all RIP enabled devices. Device is ready for new WPS to setup. Gently fasten the two slots with the screws. Step 3 Slowly take your hands off the device. Ensure that manuaal device is properly mounted on the wall with the support of the screws. See the following figure: If wireless security is used, the wireless workstations must be properly configured for the security settings used.

This setting can be changed in the WAN Settings window of the web management interface.

A factory reset will erase the current configuration settings and reset them to the default settings. If wireless security is used, the wireless clients must be configured with the correct security information to use the Router. More information on configuring the wireless settings is found later in this manual. When you manage the Modem through Web, you must keep the Modem power on. Otherwise, the Modem may be damaged. You need to reboot the DSL router to enable your dsl-640b or configuration effective in some cases, for example, after you modify the PVC configuration.

Some modification, such as adding a static route, takes effect at once, and does not require modem reboot. If you have not configure the PPP connection, the system will remind you. The user name or password can only be less than 16 characters. To ignore the step, click Skip. After proper configuration, the right page appears. In this page, you can set the Internet time. The virtual path between two points in an ATM network, ranging from 0 to The virtual channel between two points in an ATM network, ranging from 32 to 1 to 31 are reserved for known protocols Connection mode: Your ISP should provide manuxl with the following dsl-264b You can select the Network authentication from the drop-down list.


You can select the WPA Encryption from the drop-down list. Click Cancel to cancel the configuration. Click Advance Setup to continue other settings. In the current software version, three virtual access points can be configured. Click Apply to save the basic wireless options and make the modification effect. You can set 4 types of the WEP key. The authentication modes vsl-2640b as follows: After proper configuration, click Mmanual to save the wireless security options and make the modification effect.

You can mankal it from the mankal list. Enable Quality Of Service: Enable or disable QoS. After proper configuration, click Next and the right page appears. In this page, you can set the service description, enable If you enable After proper configuration, click Next.

Select the checkbox to apply Fullcone NAT mode. Use Static IPv6 Address: Enable to use a static IPv6 address.

D-link DSL-2640B User Manual

Enter the address in the IPv6 Address field. In this page, select a preferred WAN interface as the system default gateway. Click Next, and the right page appears.

In this page, it shows all the configurations. Click Back to make any modifications. Then it turns to the Quick Setup page. Web Configuration After proper configuration, click Next and the right page appears. Indicates if MLD is enabled or disabled. Back Click to return to the previous configuration screen Next Click to proceed to the Routing — Default Gateway window.

In this page, you can set the service description.


The preset IP address is Click Add Entries, the following figure appears. If you want to configure the second IP, please select the check box. Select Static to specify a static IPv6 site prefix. Site Prefix Enter the IPv6 site prefix.

Site Prefix Specify the length of the IPv6 site prefix. Length Enable Select the checkbox to enable multicast listener discovery Snooping snooping. Apply Click to save changes. The selected WAN service. Click to add a DDNS service. Enter the access username dsl-264b0 the DDNS service. Password Enter sdl-2640b password. In this page, you should enter the email and key. Tick the text boxes of the modulation types you want to enable.


Choose the Inner pair or Outer pair option by clicking the appropriate radio button. Tick the text boxes of the capability options you want to enable. Select the desired DSL test mode and then click the Apply button.

Web Configuration Click the Tone Selection button to modify the upstream and downstream tones. Manhal the appropriate upstream and dsl–2640b tones for your ADSL connection. Click the Apply button to let your settings take effect.

Click Virtual Server, and the right page appears. The port forwarding virtual server page is used to define applications that require special handling by DSL router. Click Apply to apply the settings. If majual application you require is not in the dsl-26440b, manually enter the information. Select the Remove check box. Click Remove to remove the settings. Enter the local IP address of the PC that is to be enabled as an exposed host. Click IP Filter and the right page appears.

By default, the firewall is enabled.

The firewall is used to block document transmissions between the Internet and your PC. It serves as dso-2640b safety guard and permits only authorized documents to be sent to the LAN. However, some IP traffic can be accepted by setting up filters. Click Apply to save and activate the filter. You should select at least one WAN interface to apply this rule.

You can select the protocol from the drop-down list. All specified conditions dsl-640b the filtering rule must be complied with the rule to take effect. Blocked means that all MAC layer frames are blocked except those matching with any of the specified rules in the following table. Click Change Policy and the following page apperas. Web Configuration Click Add, the right page appears. dsl-2640bb


You can select the protocol type from the drop-down list. After proper configuration, click Apply. LAN device where the browser is running. The interface that the packets pass through on the modem.