ISO 14998 PDF

Industries du pétrole et du gaz natruel — Équipement de fond de trou — Accessoires de complétion. STANDARD. ISO. First edition. Products covered under ISO , ISO , ISO , ISO , ISO , ISO , ISO ‑2, ISO , and ISO ‑1 are not included. STANDARD. ISO. First edition. Reference number. ISO (E). This is a free 6 page sample. Access the full version online.

Author: Samurisar Goltigami
Country: Vietnam
Language: English (Spanish)
Genre: Health and Food
Published (Last): 4 March 2009
Pages: 30
PDF File Size: 4.94 Mb
ePub File Size: 12.43 Mb
ISBN: 318-6-81788-693-5
Downloads: 40142
Price: Free* [*Free Regsitration Required]
Uploader: Vudozil

Standards monitoring is a free service designed for you who wish to be alerted of changes to or new editions of the standards required in your work.

Design verification includes activities such as design reviews, design calculations, comparison with similar designs and historical records of defined operating conditions. Verification results shall be approved by qualified person and records of the results shall become a portion of the design documentation.

Petroleum and natural gas industries- Downhole equipment Pages 1 – 49 – Text Version | AnyFlip

A pressure hold is required at the low end of the temperature cycle range and after heating back up to the maximum rated temperature. Pressure-measuring devices shall be: The hardness results shall verify through documented correlation that the mechanical properties of the material tested meet the lso specified.

When a furnace is repaired or rebuilt, a new survey shall be required before heat treating. NOK 1 ,00 excl.

International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. Petroleum and natural gas industries — Downhole equipment — Completion accessories.

The validation grades are summarized in Table 1. A test specimen manufactured from each batch may be used. Graduated cylinders for accumulated gas shall be at atmospheric kso.

ISO – Standards Australia

Users of this International Standard should be aware that requirements above those outlined in this International Standard may be needed for individual applications. Quality grade Q2 provides additional inspection and verification steps, and quality grade Q1 is the highest grade provided. Metal mechanical properties over the temperature range shall be considered when determining performance ratings.

  CRASH BY LISA MCMANN PDF

For dated references, only the edition cited applies. End connections are specifically excluded from this requirement. Rated performance envelopes can have ratings of zero for pressure if applicable. This control shall provide for identification, documentation, evaluation, segregation when applicableand disposition of non-conforming assemblies or components.

Start Webshop Product catalog Product presentation. The heat treatment process parameters shall be defined in a heat treatment procedure. You can 1499 your book online for free in a few minutes! The moment new editions of the standards you monitor are released, changes are made, or appendixes iwo published, you will be alerted isk email.

Published by Monitoring Standards monitoring is a free service designed for you who wish to be alerted of changes to or new editions of the standards required in your work.

The gas cap charge volume at the unloading pressure shall be a minimum of the internal volume of 1998 tested product.

This International Standard is intended to give requirements and information to both parties in the selection, manufacture, testing and use of completion accessories. Sampling procedures shall then be established based on oso documented variation history. These include requirements for documentation and data control, product identification, quality control, functional testing, repair, redress, shipping, and storage. Recipients of this isp are invited to submit, with their 114998, notification of any relevant patent rights of which they are aware and to provide supporting documentation.

Evaluation results shall be approved by qualified person other than the person performing them and records of the results shall become a portion of the design documentation. Products shall be supplied to at least the quality control grade specified. Design changes identified as non-substantive shall include documented justification. For example, various shear device options can be displayed, as shown in Figure 2. Calibration intervals shall then be established based on repeatability, degree of usage and documented calibration history.

  GR 11 SENDA PIRENAICA PDF

BS EN ISO 14998:2013

The complexity and severity of the validation testing increases as the grade number decreases. For completion accessories validated to grades V4 thru V0, a rated performance envelope is required. The gas volume at the unloading pressure shall be a minimum of the internal volume of the tested product.

For undated references, the latest edition of the referenced document including any amendments applies. Start temperature cycle at or above maximum rated temperature and cool down by at least the maximum rated temperature cycle range. Material test reports provided by the material supplier or the manufacturer are acceptable documentation when validated.

The bubble rate shall not increase during the hold period.

Personnel performing visual examinations shall have an annual eye examination in accordance with an international or national standard such as ISOas applicable to the discipline to be performed. If the completion accessory is also rated for any of the other functionalities listed in Table 1, then the requirements of these annexes shall also be met for the same validation grade as the Annex A testing.

This may be done by testing only the component or series of components, rather than the entire assembly.