ASTM D1044 PDF

ASTM D SURFACE ABRASION. This test method describes a procedure for estimating the resistance of transparent plastics to one kind of surface. the ASTM D abrasion resistant test by showing less than. 5% scattered light and haze after being abraded. 3M Construction Markets. ASTM D Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion. This test method describes a procedure for estimating the.

Author: Mojora Dalar
Country: Kuwait
Language: English (Spanish)
Genre: Medical
Published (Last): 8 September 2005
Pages: 385
PDF File Size: 7.81 Mb
ePub File Size: 4.80 Mb
ISBN: 827-8-12778-615-5
Downloads: 97013
Price: Free* [*Free Regsitration Required]
Uploader: Tajas

This specification describes the general requirements for test equipment used in testing electrical and electronic equipment. This norm specifies a method for the determination of resistance to abrasion for paints, varnishes and products when using the Taber Abraser. NASTA Manufacturing Standards and Specifications for Textbooks If offset printed on coated cover material, a protective top coating for abrasion resistance is required. Link to Active This link will always route to the current Active version of the standard.

A, or gram load is placed on top of the abrader wheel and allowed to spin for a specified number of revolutions.

Transparent Plastic Digital Haze Meter , Transmission Haze Measurement ASTM D1044 Standard

EN Resilient floor coverings – Determination of wear resistance – Part 2: The method is adapted in order to compare various finish, or as a control test in order to assure that a determined level of furniture surface performance is maintained and applied to all.

This specification does not address, and therefore is not applicable to, ground-face concrete masonry units that are manufactured by grinding a thin layer off the surface of a concrete masonry unit to expose aggregates within and polishing to produce smooth, architectural finish.

It can be used to determine the wear resistance of surfaces against abrasion and particularly for ranking different wear layer types within one type of product. This document specifies two alternative test methods to determine the resistance to wear of lacquered wood floorings and one method to test the elasticity of the lacquer.

Tape shall consist of glass spheres of a high optical quality imbedded into a binder on a suitable backing that is pre-coated with a pressure-sensitive adhesive.

ASTM D1044

Some test methods are included, but most sections refer to specific ASTM test methods. The test measures the ast, of a decorative surface of the sheet under test to resist abrasive wear through to the sub-layer.

This specification covers the requirements for six types and two classes of electrolytically formed anodic coatings on aluminum and aluminum alloys for non-architectural applications.

This International Standard specifies requirements for hard anodic oxidation coatings on aluminum and its alloys, including test methods. It is applicable to non-filled synthetic turf with a pile height greater than 15mm.

  EL FILOSOFO DE GUEMEZ LIBRO PDF

This method is intended for determining the abrasion resistance of cloths in terms of percent change in breaking strength, or breaking strength after a given period of abrasion, or the number of abrasion cycles required to produce a specified state of destruction. The below links summarize popular Taber test methods and are sorted by application e. To determine the abrasion resistance of chemical coated fabrics and films using a rotary platform double head tester.

The purpose of this test is to determine whether safety glass has a certain minimum resistance to abrasion. Global Reach Intertek is the industry leader with over 42, people in 1, locations in over countries. ISO Paints and Varnishes; Determination of Resistance to Abrasion This part of ISO specifies a method for determining the resistance to abrasion of a dried film of paint, varnish or related product, using abrasive paper attached to wheels and abrading by making a rotary movement ISO Paints and Varnishes; Determination of Resistance to Abrasion This part of ISO specifies a method for determining the resistance to abrasion of a dried film of paint, varnish or related product, using abrasive rubber wheels and abrading by making a rotary movement ISO Plastics; Determination of Resistance to Wear by Abrasive Wheels This International Standard specifies a general method for determining the resistance to abrasive wear of plastics under the action of abrasive wheels.

Thin, Hard, Dense Deposit This specification covers the engineering requirements for the deposition of a thin, hard dense chromium coating on surfaces of ferrous and non ferrous alloys and the properties of the coating.

This specification covers minimum material performance and laboratory test procedures for non-reinforced liquid coating encapsulation products single or multiple-coat systems for leaded paint in buildings. Abrasion can be difficult to compare but haze variation or weight loss are often evaluated.

This specification covers general and performance requirements for curved polycarbonate flyer’s helmet visors worn by aircrew personnel. This Standard applies to high pressure decorative laminates for use as work and nonwork surfaces of food service equipment on which direct food contact during normal preparation or holding operations is not intended, expected, or reasonable. Comparisons of data using these wheels should be made with caution. MIL-DTLF General Specification for Connectors, Plugs and Receptacles, Electrical Waterproof, Quick Disconnect, Heavy Duty Type This specification covers multicontact heavy duty, quick disconnect, waterproof, electrical plug and receptacle connectors and associated accessories for electronic and electrical power and control circuits.

This guide covers the selection and use of procedures for testing traffic paints in the laboratory and in the field. LAT Hard Anodizing This method covers the requirements for anodization of aluminum and it alloys MIL-AF 1 Military Specification – Anodic Coatings for Aluminum and Aluminum Alloys This specification covers the requirements for six types and two classes of electrolytically formed anodic coatings on aluminum and aluminum alloys for non-architectural applications.

  GRAFICKA INDUSTRIJA PDF

Two test methods are included. Portable Elbow Slip Tester Load: This test method quantifies the abrasion resistance of metallic coatings produced by thermal spray processes on flat metallic surfaces.

It is the purpose of this test method to provide a means of estimating the resistance of such materials to this type and degree of abrasion. The method is used on coated wood, foiled and laminated substrates in applications where high surface resistance is required. It is the responsibility of the user of this standard to establish appropriate safety and health practices and f1044 the applicability of regulatory limitations prior to use.

This guide provides a common basis on which protective coatings for the surfaces of light water-moderated nuclear power generating facilities may be qualified and selected by reproducible evaluation tests. Through our network of over 43, people in d044, laboratories and offices in countries, Intertek provides quality and safety solutions to a wide range of industries around the world.

This SAE recommended practice covers the requirements for rubber floor mats made from five types of rubber compound as required by the physical property requirements of the application. The specification applies only to a membrane system that has an integral wearing surface.

ASTM-D Taber Abrasion Test Equipment For Suitcases / Carpets / Furniture

This specification covers adhesive-backed metal foil identification or instruction plates, herein referred to as identification plates, for use as internal and external equipment identification or instruction see 6. This test methods covers the establishment of an index of abrasion resistance by determination of loss of weight resulting from abrasion of dimension stone.

EN Annex E Laminate floor coverings – Elements with a surface layer based on f1044 thermosetting resins – Specifications, requirements and test methods This annex specifies the method for measuring abrasion resistance and consequently determining the abrasion class of laminate floor covering d1044.

Applications of high pressure decorative laminates covered by atsm Standard include wait stations, service counters, and other counters when used in conjunction with cutting boards or other means of preventing direct food contact with the laminate. All drawings are examples only; other forms are permissible. It is equally applicable to moulded test specimens, components and finished products.