ASTM B BM 08 Standard Specification for Copper Alloy Continuous Castings_机械/仪表_工程科技_专业资料。ASTM B BM Chemical Composition according to ASTM B/BM 1Ni value includes Co. Note: Cu + Sum of Named Elements, % min. Single values, unless. ASTM B/BM Standard Specification for Copper Alloy Continuous Castings. standard by ASTM International, 03/01/ View all product details.
|Published (Last):||4 June 2013|
|PDF File Size:||10.70 Mb|
|ePub File Size:||6.21 Mb|
|Price:||Free* [*Free Regsitration Required]|
Mechanical tests are required only when specified by the purchaser in the purchase order. The cross sections are the diameter of a round solid, qstm distance across the?
If a Brinell hardness is required and a tension test is not required, testing shall be in accordance with Test Method E Sul- Phosfur zstm 0. C high-leaded tin bronze No further reproductions authorized. In such cases the manufacturer shall maintain heat traceability to specific manufacturing date and chemical analysis.
Historical Version s – view previous versions of standard. Newsletter Sign Up Email.
ASTM B505 SAE 660 Bronze
Other terms for this alloy are: They are a combination of the calculated theoretical weights and an average of actual weights. Test bar specimens shall be positively identi? Weld repairs may be made at the manufacturer’s discretion. Active view current version of standard. Limits may xstm established and analysis required for unnamed elements agreed upon between the manufacturer or supplier and the purchaser.
Pressure-containing castings weighing less than 50 lb C leaded tin bronze 80 16 The weights listed are the best estimates of the actual weights we will ship. C nickel-tin bronze astk The fractured bars shall be retained for chemical verification.
ASTM B BM 08 Standard Specification for Copper Alloy Continuous Castings_百度文库
Analysis shall be made for residual elements only when speci? Actual practice may vary by manufacturer. It just another part of value we offer at Morgan. If the wall thickness is 1?
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Link to Active This link will always route to the current Active version of the standard. This standard has been approved for use by agencies of the Department of Defense.
C, C, C, and C may be supplied in the heat-treated condition to obtain 4 the atm mechanical properties shown in Table 9. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
The specimen shall be comprised of the following major elements: Other major element chemical requirements: C leaded naval brass 61 1 1. C tin bronze The suffix can be used to accommodate composition variations of the base alloy.
C manganese nickel aluminum In addition, heat numbers, or serial numbers that are traceable to heat numbers, shall be marked on all pressurecontaining castings individually weighing 50 lb Applicable to any longitudinal surface or edge.
F Chromium content shall asgm 0. C aluminum bronze This specification establishes requirements for continuously cast rod, bar, tube, and shapes produced from copper alloys g505 nominal compositions. C Bronze is a general-purpose bearing alloy possessing good anti-friction properties, ample strength and hardness, adequate ductility and excellent machinability.
In such cases the manufacturer shall maintain heat traceability to aztm
Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Users of this standard are expressly atsm that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. F As cast or temper annealed. Our weights are conservative to the heavier side but there may be slight variations in weight from bar to bar.
It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Your comments are invited either for revision of this standard or for additional standards asfm should be addressed to ASTM International Headquarters. Contact our QA department for clarification. H Chemical requirements for other elements: Propeller castings shall be exempt from this requirement.
Combining values from the two systems may result in non-conformance with the standard.