L. S. L. Elements. (C) Carbon, max. (Mn) Manganese, max. Amardeep Steel Centre is one of the leader manufacturers, Supplier and exporters of high quality ASTM A Stainless Steel Rectangular Tube, ASTM A Global Steel is one of the leading manufacturers, Supplier and exporters of High Quality ASTM A Steel Pipes, ASTM A Polished Stainless Steel Pipes.
|Published (Last):||26 October 2013|
|PDF File Size:||1.99 Mb|
|ePub File Size:||3.58 Mb|
|Price:||Free* [*Free Regsitration Required]|
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Tensile Strength, min ksi MPa. A Grade Tube. Material meeting the requirements of S, S, or S may, by agreement between purchaser and a54, be certified as S Unless otherwise specified in the ordering information, an order specifying S or Typeshall be satisfied by any one of S, S, or S at the option of the seller.
Radii of Corners, max. The grades covered are listed in Table 1.
A polished stainless steel ornamental tubes are widely used for building constructions and architectural applications. The average of maximum and minimum outside diameter readings should fall within the outside diameter tolerances as shown in this table. Yield Strength min, ksi MPa.
astm a,astm a tubing,astm a stainless steel tubing,astm a square tubing
B For ovality values, the tolerance for average outside diameter at any one cross section does not exceed the outside diameter tolerance value for the applicable outside diameter.
The straightness tolerance is 0. For sizes up to and including 5-in. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. A Grade L Tube. Zstm values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Click here For more ss material price list. Where ellipses … appear in this table, there is no minimum and analysis for the element need not be determined or reported.
It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and a5554. Tolerances Hot Finished Round Table.
ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. The tubes shall be made from flat-rolled steel by an automatic welding process without the addition of filler metal.
Up to 6 meters, custom cut lengths Thickness: Largest Specified Outside Dimension, Inches.
ASTM A554 Stainless Steel Pipe/ Tube manufacturer & suppliers
Tolerances — Diameter, Wall— Round Tubing. Elongation in 2 in. Astk meeting the requirements of S, S, or S may, by agreement between purchaser and manufacturer, be certified as S Ratio of Wall Thickness to Outside Diameter.
This guide covers standard specification for welded stainless steel tubing for mechanical applications where appearance, mechanical properties, or corrosion resistance is needed. Specified Size, Outside Diameter, In.
ASTM A554 304/304L/304H Stainless Steel EFW Tubes
This abstract is a brief summary of the referenced standard. Bright Annealed, Polished Trade Name: Therefore, the wall thickness can vary 15 percent over and under that specified, and the inside diameter is governed by both the outside diameter and wall thickness tolerances.
Heat analysis shall be performed wherein aa554 grades of steel shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, silicon, nickel, chromium, molybdenum, titanium, columbium, and tantalum.
A These tolerances apply to cut lengths up to and including 24 feet. Also see Footnote B. Small outside diameter tubes are defined as those less than 0.
Permissible Variations in Zstm Length in. Tied with steel trips, then wrapped by plastic material. A welded stainless steel tubing for mechanical applications where appearance, mechanical properties, or corrosion resistance is needed in a number of standard sizes and grades. For square or rectangular structural tubing with heavier walls, the radius of any outside corner of the section shall not exceed three times the specified wall thickness. Historical Version s – view previous versions of standard.
For sized over 5-in. E These tolerances apply to cut lengths up to and including 24 feet.