ASTM A265 PDF

ASTM A ASME SA “Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel. Plate”. “STANDARD SPECIFICATION FOR NICKEL AND. Buy ASTM A SPECIFICATION FOR NICKEL AND NICKEL-BASE ALLOY-CLAD STEEL PLATE from SAI Global. Designation: A − 12Standard Specification for Nickel and Nickel-Base Alloy- Clad Steel Plate1 This standard is issued unde.

Author: Ferg Nezahn
Country: Zambia
Language: English (Spanish)
Genre: Technology
Published (Last): 5 July 2017
Pages: 364
PDF File Size: 4.32 Mb
ePub File Size: 14.51 Mb
ISBN: 909-1-86277-480-3
Downloads: 63041
Price: Free* [*Free Regsitration Required]
Uploader: Nezahn

If the requirements of this speci? Testing for shear strength for clad plates with minimum cladding thickness of 0.

ASTM A265 Clad Plate

NOTE 2—Punch marks for measuring elongation after fracture shall be made on the? ASTM International takes no position respecting the validity of any patent rights asmt in connection with any item mentioned in this standard. A — 09 Standard Speci? The material is generally intended for pressure vessel use but may be used in other structural applications where corrosion resistance of the alloy is of prime importance.

Chemical analysis may be accomplished by wet chemical or instrumental procedures.

If wet chemical procedures are used, millings may be taken only when the composite plate thickness is sufficient to permit obtaining millings without danger of contamination astmm the adjacent layer. These bend tests shall be made in the manner of the tension tests indicated in Fig. Historical Version s – view previous versions of sstm Translated Version s: Link to Active This link will always route to the current Active version of the standard.

This abstract is a brief summary of the referenced standard.

Historical Version s – view previous versions of standard. This standard has been approved for use by agencies of the Department of Defense. The base metal shall be carbon steel or low-alloy steel conforming to the specifications for steels for either pressure vessels or for general structural applications.

The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. The base metal shall conform to the chemical requirements of the speci? If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

  ICEA S-95-658 PDF

ASTM A GR 1 titanium alloy strip sheet plate

The material shall be cleaned and sufficient millings taken to represent the full cross-section of the remainder. The tensile properties thus determined shall meet the base steel requirements.

This specification covers the standard for plate of a carbon steel or low-alloy steel base to which is integrally and continuously bonded on one or both sides a layer of nickel or nickel-base alloy.

If spectrometric procedures are used, the sample shall be exposed on the center line of the cladding when there is sufficient cladding thickness available so that there is no contamination from the adjacent base metal. The nickel or nickel-base alloy cladding metal shall conform to prescribed chemical composition. Such requirements may include, but are not limited to the following: Permissible Variations Metric Equivalents in.

Materials and Manufacture 5. The shear test, when speci?

The minimum cladding thickness for shear testing shall be 0. The reduced section shall have a gradual taper from the ends toward the center, with the ends 0.

The properties thus determined shall meet all of the tensile test requirements for the base steel. Product and chemical analyses shall be performed on the cladding alloy and be accomplished by wet chemical or instrumental procedures. Originally approved in General Requirements for Delivery Gage Length cladding and the base steel a2265 be machined so as to maintain the same ratio of clad metal to base steel as is maintained in the plate, except that the thickness of the clad material need not be reduced below 1?

Number of Tests and Retests 8. The sides of the bend test specimen used for bond strength determination may have the corners rounded to a radius not over 1?

Your comments will receive careful consideration asrm a meeting of the responsible technical committee, which you may attend. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

  DRUNVALO MELCHIZEDEK MAYAN OUROBOROS PDF

The surface condition of the repaired area shall be restored to a condition similar to the rest of the cladding.

ASTM A265 GR 1 titanium alloy strip sheet plate

Ultrasonic Examination in accordance with Speci? Greater separation shall be cause for rejection. The composite plate shall undergo shear strength test, bond strength test, and tension test and shall conform to the required a65 strength and yield strength.

Each specimen shall be in the? Method of test and acceptance standard shall be as agreed upon between the purchaser and the manufacturer. The steel shall be made by the open-hearth, electric furnace aatm separate degassing and refining optionalor basic-oxygen processes, or by secondary processes whereby steel made from these primary processes is remelted using, but not limited to electroslag remelting or vacuum arc remelting processes.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not wstm as part of the standard. For purposes of de? Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

ASTM A Clad Plate | ASTM A Plate | ASTM A Nickel Coated Plate

A number in parentheses indicates the year of last reapproval. NOTE 3—The dimension t is the thickness of the test specimen as provided for in the applicable material speci? Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. A list of standardized supplementary requirements for use at the option of the purchaser are included in Asgm