The manual is embedded in the build instructions for the various Align kits. This appears to come out of the manual. At least its identical to. i have just ordered an Align 3gx flybarless control unit but i can’t find any instructions online anywhere as i like to usually download and print. I have put together the written info on the Align 3GX v I found so far. Mostly for my own memory. I shrunk this info to a Pocket Guide that I will printout (or read.

Author: Vura Samudal
Country: Namibia
Language: English (Spanish)
Genre: Life
Published (Last): 25 September 2011
Pages: 260
PDF File Size: 19.25 Mb
ePub File Size: 5.95 Mb
ISBN: 607-7-58123-788-4
Downloads: 96954
Price: Free* [*Free Regsitration Required]
Uploader: Galabar

And yes you remove the bind plug while still powered, it sets fail safes, throttle etc. This completes the aileron endpoint setup process. This completes the rudder endpoint limit adjustment for the left side. It’s a must and to be used with the dongle via usb port on the PC.

Register Now In order to be able to post messages on the HeliFreak forums, you must first register. Mostly for my own memory. Originally Posted by bad What software, this software.

Align 3gx pdf manual

Based on the 3G FL manual setup process, the 3GX can be setup in a few minutes through a simple process. In addition, the 3GX can support all of the CCPM swashplate system currently on the market including 90, and degrees swashplates. Suitable for helicopter of all class from toglow engine or electric powered.

Press the SET button to enter A. What software, this software. Support with APS gyro system and bring up more functions for your helicopter. Set the right aileron and front elevator to 8 degrees. For tail pitch adjustment, center the rudder servo by either setting the 3GX flybarless to normal rate mode non-heading lockor press and hold the SET button for 2 seconds. If you use the software there are text and pop-ups to explain the settings: Please double check this.


The dramatically improved performance will create immediate impact on any enthusiasts. Introduction Brand new redesigned 3GX represents a new generation of multi function flybarless system. Wait for some sort of jingle or series of flashing lights then release bind button Does that sound right? Check that there is no binding throughout the pitch range. Hem 3GX v 2. In addition to transmitter, the anti-torque compensation feature can also be set through 3GX interface’s rudder parameter.

Plug in flight battery 3. With the APS gyro, the helicopter will have the ability to self stabilize, hold position as well as altitude, and even autonomous way point flights as well as return home. If needed, servo reverse is done from the transmitter’s REV reverse function.

Align 3gx pdf manual | Model Flying

With 3GX in operation mode, push rudder to left or right, and press the SET button for about a second. For the rest of the setup: This is clearly noticeable in stable hover as well as highly aerobatic routines.

Therefore, BEC output capability should be confirmed to handle burst current when setting collective pitch acceleration, otherwise insufficient current supply may result in flight accidents.

Manuql HK 3GX setup. Check that there is no binding throughout the pitch range 3. Originally Posted by Tulo. I have 2 sats, so would I just: Se manyal Calibration” at the end. Value should be tuned under actual flight conditions by increasing to the maximum gain without tail hunting. Confirm the rudder settings by pushing the SET button. Power on Futaba 10C 5.


To achieve consistent gyro gain on left and right, 3GX has built in anti-torque compensation function. Press 3gz hold the SET button while powering up the receiver. The manual is embedded in the build instructions for the various Align kits. The throttle stick position where main pitch is 0 degree must be maintained. Just leave the servo horns off until your in setup and install them as close to level as poss at mid stick. With all channels stationary, move the transmitter aileron stick to the right and then back to center position.

If incorr ect movements or servo has no movement, please check servo connection to 3GX as well as radio control system.

That’s kinda what I figured thanks! Gyro gain For radio with built in gyro gain settings, gain can be adjusted directly. Settings export feature allows custom settings to be shared manaul friends. Tilt the helicopter right as shown in diagramand check if swashplate is tilting correctly toward the left.

Dual axis plus rudder sensor dramatically improves swashplate and rudder correction precision compared to last generation 3G. Push the transmitter rudder stick left or right to select the 3vx rate. Password Please enter a password for your user account. Anti-torque To achieve consistent gyro gain on left and right, 3GX has built in anti-torque compensation function.

Only right aileron and front elevator measurement is needed.